If you have a defect Kitchenaid or Hobart, please contact us by telephone or with the  form below on this page.

Of course, the repair price depends on what is wrong with your machine. We have no research costs. The costs for repair are the labor hours worked and the materials used. The defective materials of your machine that we replace always come with the machine so that you can see where and what is defective, and where it went wrong. 

Please fill in so complete as possible. We can give you than a better estimate of the costs. Mostly the price of repair are between the €80,00 and € 250,00.

 

 

     Fill in the form below and send it to us together with your machine.

Repair form

Date

 

Name

 

Address

 

ZIP code/ City

 

Type machine

 

Color Machine

 

Phone number(s)

 

E-mail Address

 

 

 

Description of the problem?

 

 

 

About costs:

What can be the maximum repair costs?

 

 

 

 

Kostenadvies:

Wat mag het maximaal kosten?

How did you find us?

________________________________________________________

                             

 

 
   

Note: Please fill out the fields marked with an asterisk.

JP99, 3400025 Kitchenaid screw, replacement part

JP99, replacement part for the screw 3400025. This is not the original screw.  The costs for the original is very high. That is why  we have made this screw in the Netherlands.

€ 2,00

  • 0,01 kg
  • Available
  • deliverytime: 3-5 dagen

JP98 Locking Knob

JP98

The JP98 is only the locking knob with M10 thread to additionally secure the head of your food processor so that it shakes less back and forth and up and down during kneading or mixing. This button is for self-assembly and not a set with tap. See the JP98set for this. For how to mount it see the JP98set below here.

€ 9,95

  • 1 kg
  • Available
  • deliverytime: 3-5 dagen

JP98set, locking knob set

 

Locking Knob set JP98set 

 

JP de Jong Parts, Willaertpark 15, 5144VN Waalwijk, T 0416 336261, info@dejongparts.biz 

Open on Mon, Wed and Fri. morning from 9.00-11.00 for pick up and drop off.

 

JP98set, is a set with the locking knob with M10 thread, and the tap M10 for tapping the thread. First pre-drill the hole with 4 mm and then 8.0-8.2 mm, measured 20 mm center to center above the hole in which the hinge pin is located. You drill this hole of 8.0-8.2 mm all the way through the machine so that you can see the hole on the inside. Of course, you must first have separated the top of the machine from the bottom of the machine by removing the hinge pin. Grease the machine tap with a cutting compound, then thread it through the drilled hole. Make sure that the thread also comes through the inner wall. See the pictures. If you have any questions, you can contact us. We can also do it for you. The costs are then currently complete with button € 50.00 incl. VAT. However, without shipping costs from the machine back to you. Shipping costs of your machine are € 20.00. Your machine is always sent insured, or you bring it and collect it from us.

 

Procedure: 

1, If you have laid the machine on its side, loosen the locking screw of the hinge pin a few turns. 

2,Turn the machine upright and drive the hinge pin out of the machine with a thin punch. Be careful not to     drop the machine head. 

3, Mark where the hole should be. 20mm center to center to the hinge pin hole. 

4, Drill the 4mm hole perpendicular to the hinge mounting and parallel to the hinge pin hole so that you  can see it on the inside of the hinge. 

5, Then drill this with the drill 8.0 – 8.2mm. 

6, Tap the thread parallel to the hinge pin hole and be careful not to tap the thread crooked!! 

7 ,The thread tap should be visible inside the hinge if all is well.

8, Yes, then it is good. If not then you have a problem!! Then you have tapped the screw thread crookedly.  We can remedy this for you at our factory with a Helicoil. This is a new screw thread with spiral so that it still fits. 

9, If you have any questions, please contact us at info@dejongparts.biz or T. 0416 336261. 

10, Good luck and enjoy your extra lock button

 

€ 29,49

  • 1 kg
  • Available
  • deliverytime: 3-5 dagen

JP97, spring JPV13

Spring JPV13 for the Kitchenaid Artisan, Classic and all other Kitchenaid Kitchen Robots like;  5KSM125-195, That do not have a spring on the shaft where you attach your kneading hook, whisk or beater.

Fits also;

Kenwood Patissier,

AEG Ultramix KM4000, KM4400, KM5520, KM5540, KM5560

Sunbeam MX7900, MX9200, MX9500,

Espressions of Australia Planetary Mixmaster EP9200,

Solis Kitchen Queen Pro 808,

Smeg SMF01.

Magnani MI-HA-MFKM1-R,

Elektrolux EKM 4100,

Hobart K45.

Eisenbach SC-263

Tarrington House SM 2000

Herman de Blijker 2012

Domo Kitchen Robot, DO 9074KR, 75KR, 76KR, etc.

 

Spring for the Agitator Shaft to keep the Attachment like your Dough hook, Beater, Pastry Knife or Whisk on his place.

Very important to have this on your machine!!

 

For mounting the Spring on the Agitator Shaft, look at the video on the right side of this page from the Domo 9074 Kitchenrobot.

Or see this link; https://youtu.be/8o8u2au_Q-Y

€ 5,95

  • 0,01 kg
  • Available
  • deliverytime: 3-5 dagen

JP96, protection plate

 

 JP96, This is a protective plate that can be mounted above the beater, dough hook or whisk to prevent splashing against the head of the machine. Even with bread dough with little moisture, it can happen that the dough climbs into the dough hook and soils the machine. Easy to mount on the machines that already do not have a protective plate. Can be easily removed for cleaning by hand or in the dishwasher.

Stick it up on the shaft past the pin and then turn it until it can't go down.

 

Fits All Kitchenaid machines,

Kenwood Patissier,

AEG Ultramix KM4000, KM4400, KM5520, KM5540, KM5560

Sunbeam MX7900, MX9200, MX9500,

Espressions of Australia Planetary Mixmaster EP9200,

Solis Kitchen Queen Pro 808,

Smeg SMF01.

Magnani MI-HA-MFKM1-R,

Elektrolux EKM 4100,

Hobart K45.

Eisenbach SC-263

Tarrington House SM 2000

Herman de Blijker 2012

Domo Kitchen Robot, DO 9074KR, 75KR, 76KR, e

 

Made in the Netherlands, from stainless steel by superdoughhook.com

€ 5,95

  • 0,01 kg
  • Available
  • deliverytime: 3-5 dagen